徐工RP951沥青摊铺机配件及维修

夯锤泵连接盘#D-48407RHEINE#171600

文章出处:工程机械之家http://www.700618.com/人气: 发表时间:2023-03-14 10:45:53

 夯锤的工作原理:夯锤由偏心轴驱动,实现上下运动,从而压紧熨平板下方的材料。为了获得更高的预压实度,应该根据特定的层厚和摊铺速度正确的设置夯锤。

福格勒摊铺机夯锤调节比例为:根据1米每分钟夯锤的转速同步增加。夯锤的转速随摊铺速度的加大而加大,一般进行沥青摊铺时,起步时夯锤转速的设定:底层选择10%(摊铺厚度8-10公分)中面层摊铺选择6%(4-6公分),根据试验段的结果确定最终的起步速度的设定,然后根据1米每分钟夯锤的转速同步增加,在同批次材料摊铺中,摊铺速度与夯锤的比例不能随意修改。

 

免责声明丨 部分内容来源网络!本文仅供交流学习 , 版权归属原作者,部分图片、内容推送时未能及时与原作者取得联系,若来源标注错误或侵犯到您的权益烦请告知,我们将立即删除.

企业介绍

公司供应摊铺机配件,压路机配件,铣刨机配件,摊铺机刮板驱动轴,刮板驱动轴总成,找平仪,找平仪支架以及液压泵和配件。我厂还供应摊铺机易损件,摊铺机平衡梁,搅龙轴,踏板,输料底板,叶片,熨平板,减速机,链轨,履带板,支重轮,刮板大链条,输料链条等。

 

联系人:梁经理

联系方式:13645201509(微信同号)

 

QQ:2870202745

Working principle of rammer: driven by eccentric shaft, the rammer can move up and down to compress the material under the screed. In order to obtain a higher degree of precompaction, the rammer should be set correctly according to the specific layer thickness and paving speed.

 

The adjustment ratio of the hammer of Fogler paver is: increase synchronously according to the speed of the hammer per minute. The speed of the rammer increases with the increase of the paving speed. Generally, when paving asphalt, the setting of the speed of the rammer at the start: 10% (paving thickness 8-10 cm) for the bottom layer and 6% (4-6 cm) for the middle layer paving. The final setting of the starting speed is determined according to the results of the test section, and then the speed of the rammer at 1 meter per minute increases synchronously. In the same batch of material paving, the proportion of the paving speed and the rammer cannot be arbitrarily modified.

 

Disclaimer | Part of the content comes from the network! This article is only for exchange and learning. The copyright belongs to the original author. Some pictures and content are not timely contacted with the original author when being pushed. If the source label is incorrect or infringes your rights and interests, please inform us and we will delete it immediately

 

Enterprise introduction

 

The company supplies paver parts, roller parts, milling machine parts, paver scraper drive shaft, scraper drive shaft assembly, leveling instrument, leveling instrument support, hydraulic pump and accessories. Our factory also supplies vulnerable parts of pavers, paver balance beams, auger shafts, pedals, feeding soleplates, blades, screeds, reducers, chain tracks, track shoes, rollers, scraper large chains, feeding chains, etc.

 

Contact: Manager Liang

 

Contact: 13645201509 (WeChat same number)

QQ:2870202745