徐工RP951沥青摊铺机配件及维修

三一摊铺机分动箱齿轮轴轴承#63998802

文章出处:工程机械之家http://www.700618.com/人气: 发表时间:2023-02-24 10:21:43

1、按滚动轴承结构类型分类 (1) 轴承按其所能承受的载荷方向或公称接触角的不同,分为:1)向心轴承----主要用于承受径向载荷的滚动轴承,其公称接触角从0到45。按公称接触角不同,又分为:径向接触轴承----公称接触角为0的向心轴承:向心角接触轴承----公称接触角大于0到45的向心轴承。2)推力轴承----主要用于承受轴向载荷的滚动轴承,其公称接触角大于45到90。按公称接触角不同又分为: 轴向接触轴承----公称接触角为90的推力轴承:推力角接触轴承----公称接触角大于45但小于90的推力轴承。 

2、 轴承按其滚动体的种类,分为: 1) 球轴承----滚动体为球: 2) 滚子轴承----滚动体为滚子。滚子轴承按滚子种类,又分为: 圆柱滚子轴承----滚动体是圆柱滚子的轴承,圆柱滚子的长度与直径之比小于或等于3 ;滚针轴承----滚动体是滚针的轴承,滚针的长度与直径之比大于3,但直径小于或等于5mm; 圆锥滚子轴承----滚动体是圆锥滚子的轴承; 调心滚子轴承一一滚动体是球面滚子的轴承。(3) 轴承按其工作时能否调心,分为: 1) 调心轴承----滚道是球面形的,能适应两滚道轴心线间的角偏差及角运动的轴承; 2) 非调心轴承(刚性轴承)----能阻抗滚道间轴心线角偏移的轴承。

3.按滚动轴承尺寸大小分类 轴承按其外径尺寸大小,分为: (1) 微型轴承----公称外径尺寸范围为26mm以下的轴承; (2) 小型轴承----公称外径尺寸范围为28-55mm的轴承; (3) 中小型轴承----公称外径尺寸范围为60-115mm的轴承; (4) 中大型轴承----公称外径尺寸范围为120-190mm的轴承 (5) 大型轴承----公称外径尺寸范围为200-430mm的轴承; (6) 特大型轴承----公称外径尺寸范围为440mm以上的轴承。

免责声明丨 部分内容来源网络!本文仅供交流学习 , 版权归属原作者,部分图片、内容推送时未能及时与原作者取得联系,若来源标注错误或侵犯到您的权益烦请告知,我们将立即删除.

 

 

 

 

 
企业介绍

公司供应摊铺机配件,压路机配件,铣刨机配件,摊铺机刮板驱动轴,刮板驱动轴总成,找平仪,找平仪支架以及液压泵和配件。我厂还供应摊铺机易损件,摊铺机平衡梁,搅龙轴,踏板,输料底板,叶片,熨平板,减速机,链轨,履带板,支重轮,刮板大链条,输料链条等。

联系人:梁经理

联系方式:13645201509

(微信同号)

QQ:2870202745

1. According to the structure type of rolling bearings, (1) bearings are divided into: 1) radial bearings - rolling bearings mainly used to bear radial load, with nominal contact angle from 0 to 45, according to the load direction they can bear or the nominal contact angle. According to the different nominal contact angles, it can be divided into radial contact bearings - radial bearings with a nominal contact angle of 0; radial angular contact bearings - radial bearings with a nominal contact angle greater than 0 to 45. 2) Thrust bearing - mainly used for bearing axial load, with nominal contact angle greater than 45 to 90. According to the difference of nominal contact angle, it can be divided into: axial contact bearing - thrust bearing with nominal contact angle of 90; thrust angular contact bearing - thrust bearing with nominal contact angle greater than 45 but less than 90.

2. According to the types of rolling elements, bearings are divided into: 1) ball bearings ---- rolling elements are balls; 2) roller bearings ---- rolling elements are rollers. Roller bearings can be divided into cylindrical roller bearings according to the types of rollers. The rolling body is the bearing of cylindrical roller. The ratio of length to diameter of cylindrical roller is less than or equal to 3; Needle-roller bearing - the rolling body is a needle bearing. The ratio of needle length to diameter is greater than 3, but the diameter is less than or equal to 5mm; Tapered roller bearing - the rolling body is the bearing of tapered roller; Self-aligning roller bearing - the rolling body is a spherical roller bearing. (3) Bearing can be divided into: 1) self-aligning bearing - the bearing whose raceway is spherical and can adapt to the angular deviation and angular movement between the axes of two raceways; 2) Non-aligning bearing (rigid bearing) - a bearing that can resist the angular deviation of the axis between the raceways.

3. According to the size of rolling bearings, bearings can be divided into: (1) miniature bearings - bearings with a nominal outer diameter of less than 26mm; (2) Small bearings - bearings with a nominal outer diameter of 28-55mm; (3) Medium and small bearings - bearings with nominal outer diameter ranging from 60 to 115mm; (4) Medium and large bearings - bearings with a nominal outer diameter of 120-190mm (5) large bearings - bearings with a nominal outer diameter of 200-430mm; (6) Extra large bearing - bearing with nominal outer diameter of more than 440mm.

Disclaimer | Part of the content comes from the network! This article is only for exchange and learning. The copyright belongs to the original author. Some pictures and content are not timely contacted with the original author when being pushed. If the source label is incorrect or infringes your rights and interests, please inform us and we will delete it immediately

Enterprise introductionThe company supplies paver parts, roller parts, milling machine parts, paver scraper drive shaft, scraper drive shaft assembly, leveling instrument, leveling instrument support, hydraulic pump and accessories. Our factory also supplies vulnerable parts of pavers, paver balance beams, auger shafts, pedals, feeding soleplates, blades, screeds, reducers, chain tracks, track shoes, rollers, scraper large chains, feeding chains, etc.

Contact: Manager Liang

Contact: 13645201509

(WeChat with the same number)

QQ:2870202745